May 2011 - Test - lists.nanog.org

Blocking private AS
by Thomas Magill 27 Nov '13

27 Nov '13

I am thinking about implementing a filter to block all traffic with private AS numbers in the path. I see quite a few in my table though so I am concerned I might block some legitimate traffic. In some cases, these are just prefixes with the private appended to the end but a few have the private as a transit. Is this a good idea or would I likely be blocking too much legitimate traffic? The filter I am using currently shows the following: BGP table version is 5462394, local router ID is 209.112.253.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i58.68.109.0/24 x.x.x.x 0 100 0 6130 9498 10201 65534 i *> y.y.y.y 0 6130 9498 10201 65534 i * i68.115.224.0/24 x.x.x.x 0 100 0 6130 19151 20115 65011 i *> y.y.y.y 0 6130 19151 20115 65011 i * 85.112.22.0/24 y.y.y.y 0 6130 6939 23148 64532 64532 64532 64532 64532 64532 64532 64532 64532 i *> 93.189.194.0/24 y.y.y.y 0 6130 3549 39386 39386 39386 25233 65000 47146 i * i x.x.x.x 0 100 0 6130 3549 39386 39386 39386 25233 65000 47146 i *> 96.60.243.0/24 y.y.y.y 0 6130 2828 4181 65528 i * i x.x.x.x 0 100 0 6130 2828 4181 65528 i * i96.61.232.0/24 x.x.x.x 0 100 0 6130 2828 4181 65527 i *> y.y.y.y 0 6130 2828 4181 65527 i * i96.61.233.0/24 x.x.x.x 0 100 0 6130 2828 4181 65527 i *> y.y.y.y 0 6130 2828 4181 65527 i * i96.61.234.0/24 x.x.x.x 0 100 0 6130 2828 4181 65527 i *> y.y.y.y 0 6130 2828 4181 65527 i *> 148.207.2.0/24 y.y.y.y 0 6130 2828 3257 16531 13579 65090 i * i x.x.x.x 0 100 0 6130 2828 3257 16531 13579 65090 i *> 148.207.40.0/24 y.y.y.y 0 6130 2828 3257 16531 13579 65090 i * i x.x.x.x 0 100 0 6130 2828 3257 16531 13579 65090 i *> 148.207.97.0/24 y.y.y.y 0 6130 2828 3257 16531 13579 65090 i * i x.x.x.x 0 100 0 6130 2828 3257 16531 13579 65090 i * 170.34.100.0/24 y.y.y.y 0 6130 19151 20115 65011 ? * 170.34.104.0/24 y.y.y.y 0 6130 19151 20115 65011 ? * 170.34.113.0/24 y.y.y.y 0 6130 19151 20115 65011 ? * i174.35.1.0/24 x.x.x.x 0 100 0 6130 16467 64565 i * i174.47.199.0/24 x.x.x.x 0 100 0 6130 2828 4323 15065 65123 i *> y.y.y.y 0 6130 2828 4323 15065 65123 i * i192.109.61.0 x.x.x.x 0 100 0 6130 19151 20115 65011 i *> y.y.y.y 0 6130 19151 20115 65011 i *> 196.216.249.0 y.y.y.y 0 6130 2828 3257 8513 8513 8513 36881 65000 36896 37062 i * i x.x.x.x 0 100 0 6130 2828 3257 8513 8513 8513 36881 65000 36896 37062 i Network Next Hop Metric LocPrf Weight Path *> 209.172.69.128/30 y.y.y.y 0 6130 16467 64565 i * i x.x.x.x 0 100 0 6130 16467 64565 i *> 213.146.161.0 y.y.y.y 0 6130 2828 174 64679 48493 i * i x.x.x.x 0 100 0 6130 2828 174 64679 48493 i Thomas Magill Network Engineer Office: (858) 909-3777 Cell: (858) 869-9685 mailto:tmagill@providecommerce.com <mailto:tmagill@providecommerce.com> provide-commerce 4840 Eastgate Mall San Diego, CA 92121 ProFlowers <http://www.proflowers.com/> | redENVELOPE <http://www.redenvelope.com/> | Cherry Moon Farms <http://www.cherrymoonfarms.com/> | Shari's Berries <http://www.berries.com/>

3 2

Network topology
by Colin Alston 15 Nov '13

15 Nov '13

Hi all I'm considering trying to come up with some means to automatically detect a networks topology and draw pretty pictures. This is somewhat boring though if a network isn't well arranged with VLANs and q-tag trunk routers and so on (It will just look like a big cloud of junk connected off an assumed switch). Is there any kind of cunning trick to detect standard layer2 switches along a path without stuff like STP?

9 12

Inventory and workflow management systems
by vijay gill 26 May '13

26 May '13

What software solution do people use for inventory management for things like riser/conduit drawdown, fiber inventory, physical topology store, CLR/DLR, x-connect, contracts, port inventory, etc. Any experiences in integrating workflow into those packages for work orders, modeling, drawdown levels, etc. /vijay

10 13

Re: Over a decade of DDOS--any progress yet?
by alvaro.sanchez＠adinet.com.uy 04 Oct '11

04 Oct '11

A very common action is to blackhole ddos traffic upstream by sending a bgp route to the next AS with a preestablished community indicating the traffic must be sent to Null0. The route may be very specific, in order to impact as less as possible. This needs previous coordination between providers. Regards. >----Mensaje original---- >De: rdobbins(a)arbor.net >Fecha: 08/12/2010 10:53 >Para: "North American Operators' Group"<nanog(a)nanog.org> >Asunto: Re: Over a decade of DDOS--any progress yet? > > >On Dec 8, 2010, at 7:28 PM, Arturo Servin wrote: > >> One big problem (IMHO) of DDoS is that sources (the host of botnets) may be completely unaware that they are part of a DDoS. I do not mean the bot machine, I mean the ISP connecting those. > >The technology exists to detect and classify this attack traffic, and is deployed in production networks today. > >And of course, the legitimate owners of the botted hosts are generally unaware that their machine is being used for nefarious purposes. > >> In the other hand the target of a DDoS cannot do anything to stop to attack besides adding more BW or contacting one by one the whole path of providers to try to minimize the effect. > >Actually, there're lots of things they can do. > >> I know that this has many security concerns, but would it be good a signalling protocol between ISPs to inform the sources of a DDoS attack in order to take semiautomatic actions to rate-limit the traffic as close as the source? Of course that this is more complex that these three or two lines, but I wonder if this has been considerer in the past. > >It already exists. > >----------------------------------------------------------------------- >Roland Dobbins <rdobbins(a)arbor.net> // <http://www.arbornetworks.com> > > Sell your computer and buy a guitar. > > > > > >

18 46

trouble with .gov dns?
by William Herrin 12 Aug '11

12 Aug '11

Hi Folks, Anyone else having trouble with .gov DNS failing with edns-udp-size set to 512? Here's what I'm seeing: No edns-udp-size setting. tcpdump -n -s 0 -vv -i eth1 host 209.112.123.30 or host 69.36.157.30 nslookup www.nsf.gov 127.0.0.1 11:42:36.574916 IP (tos 0x0, ttl 64, id 21833, offset 0, flags [none], proto UDP (17), length 68) 71.246.241.146.10399 > 69.36.157.30.53: [udp sum ok] 56983 [1au] A? www.nsf.gov. ar: . OPT UDPsize=4096 OK (40) 11:42:36.659636 IP (tos 0x0, ttl 249, id 54334, offset 0, flags [none], proto UDP (17), length 598) 69.36.157.30.53 > 71.246.241.146.10399: [udp sum ok] 56983- q: A? www.nsf.gov. 0/7/5 ns: nsf.gov. NS swirl.nsf.gov., nsf.gov. NS whirl.nsf.gov., nsf.gov. NS cyclone.nsf.gov., nsf.gov. NS twister.nsf.gov., nsf.gov. DS, nsf.gov. DS, nsf.gov. RRSIG ar: swirl.nsf.gov. A 198.181.231.15, whirl.nsf.gov. A 198.181.231.16, cyclone.nsf.gov. A 204.14.134.227, twister.nsf.gov. A 198.181.231.17, . OPT UDPsize=1472 (570) edns-udp-size 512 tcpdump -n -s 0 -vv -i eth1 host 209.112.123.30 or host 69.36.157.30 nslookup www.nsf.gov 127.0.0.1 11:53:01.604105 IP (tos 0x0, ttl 64, id 21834, offset 0, flags [none], proto UDP (17), length 68) 71.246.241.146.58103 > 69.36.157.30.53: [udp sum ok] 10320 [1au] A? www.nsf.gov. ar: . OPT UDPsize=512 OK (40) 11:53:01.690414 IP (tos 0x0, ttl 249, id 28744, offset 0, flags [none], proto UDP (17), length 534) 69.36.157.30.53 > 71.246.241.146.58103: [udp sum ok] 10320- q: A? www.nsf.gov. 0/7/1 ns: nsf.gov. NS swirl.nsf.gov., nsf.gov. NS whirl.nsf.gov., nsf.gov. NS cyclone.nsf.gov., nsf.gov. NS twister.nsf.gov., nsf.gov. DS, nsf.gov. DS, nsf.gov. RRSIG ar: . OPT UDPsize=1472 (506) 11:53:01.695000 IP (tos 0x0, ttl 64, id 20662, offset 0, flags [none], proto UDP (17), length 70) 71.246.241.146.23911 > 209.112.123.30.53: [udp sum ok] 18982% [1au] A? whirl.nsf.gov. ar: . OPT UDPsize=512 OK (42) 11:53:01.695489 IP (tos 0x0, ttl 64, id 20663, offset 0, flags [none], proto UDP (17), length 70) 71.246.241.146.63892 > 209.112.123.30.53: [udp sum ok] 3675% [1au] AAAA? whirl.nsf.gov. ar: . OPT UDPsize=512 OK (42) 11:53:01.695931 IP (tos 0x0, ttl 64, id 20664, offset 0, flags [none], proto UDP (17), length 70) 71.246.241.146.37019 > 209.112.123.30.53: [udp sum ok] 36777% [1au] A? swirl.nsf.gov. ar: . OPT UDPsize=512 OK (42) 11:53:01.696274 IP (tos 0x0, ttl 64, id 20665, offset 0, flags [none], proto UDP (17), length 70) 71.246.241.146.15021 > 209.112.123.30.53: [udp sum ok] 13755% [1au] AAAA? swirl.nsf.gov. ar: . OPT UDPsize=512 OK (42) 11:53:01.696653 IP (tos 0x0, ttl 64, id 20666, offset 0, flags [none], proto UDP (17), length 72) 71.246.241.146.38082 > 209.112.123.30.53: [udp sum ok] 14449% [1au] A? cyclone.nsf.gov. ar: . OPT UDPsize=512 OK (44) 11:53:01.697045 IP (tos 0x0, ttl 64, id 20667, offset 0, flags [none], proto UDP (17), length 72) 71.246.241.146.28219 > 209.112.123.30.53: [udp sum ok] 38858% [1au] AAAA? cyclone.nsf.gov. ar: . OPT UDPsize=512 OK (44) 11:53:01.699294 IP (tos 0x0, ttl 64, id 20668, offset 0, flags [none], proto UDP (17), length 72) 71.246.241.146.50745 > 209.112.123.30.53: [udp sum ok] 53248% [1au] A? twister.nsf.gov. ar: . OPT UDPsize=512 OK (44) 11:53:01.700257 IP (tos 0x0, ttl 64, id 20669, offset 0, flags [none], proto UDP (17), length 72) 71.246.241.146.21482 > 209.112.123.30.53: [udp sum ok] 56185% [1au] AAAA? twister.nsf.gov. ar: . OPT UDPsize=512 OK (44) 11:53:01.780833 IP (tos 0x0, ttl 251, id 9453, offset 0, flags [none], proto UDP (17), length 536) 209.112.123.30.53 > 71.246.241.146.23911: [udp sum ok] 18982- q: A? whirl.nsf.gov. 0/7/1 ns: nsf.gov. NS swirl.nsf.gov., nsf.gov. NS whirl.nsf.gov., nsf.gov. NS cyclone.nsf.gov., nsf.gov. NS twister.nsf.gov., nsf.gov. DS, nsf.gov. DS, nsf.gov. RRSIG ar: . OPT UDPsize=1472 (508) 11:53:01.781284 IP (tos 0x0, ttl 251, id 24142, offset 0, flags [none], proto UDP (17), length 536) 209.112.123.30.53 > 71.246.241.146.63892: [udp sum ok] 3675- q: AAAA? whirl.nsf.gov. 0/7/1 ns: nsf.gov. NS swirl.nsf.gov., nsf.gov. NS whirl.nsf.gov., nsf.gov. NS cyclone.nsf.gov., nsf.gov. NS twister.nsf.gov., nsf.gov. DS, nsf.gov. DS, nsf.gov. RRSIG ar: . OPT UDPsize=1472 (508) 11:53:01.781999 IP (tos 0x0, ttl 251, id 9454, offset 0, flags [none], proto UDP (17), length 536) 209.112.123.30.53 > 71.246.241.146.37019: [udp sum ok] 36777- q: A? swirl.nsf.gov. 0/7/1 ns: nsf.gov. NS swirl.nsf.gov., nsf.gov. NS whirl.nsf.gov., nsf.gov. NS cyclone.nsf.gov., nsf.gov. NS twister.nsf.gov., nsf.gov. DS, nsf.gov. DS, nsf.gov. RRSIG ar: . OPT UDPsize=1472 (508) 11:53:01.782136 IP (tos 0x0, ttl 251, id 24143, offset 0, flags [none], proto UDP (17), length 536) 209.112.123.30.53 > 71.246.241.146.15021: [udp sum ok] 13755- q: AAAA? swirl.nsf.gov. 0/7/1 ns: nsf.gov. NS swirl.nsf.gov., nsf.gov. NS whirl.nsf.gov., nsf.gov. NS cyclone.nsf.gov., nsf.gov. NS twister.nsf.gov., nsf.gov. DS, nsf.gov. DS, nsf.gov. RRSIG ar: . OPT UDPsize=1472 (508) 11:53:01.782552 IP (tos 0x0, ttl 251, id 9455, offset 0, flags [none], proto UDP (17), length 538) 209.112.123.30.53 > 71.246.241.146.38082: [udp sum ok] 14449- q: A? cyclone.nsf.gov. 0/7/1 ns: nsf.gov. NS swirl.nsf.gov., nsf.gov. NS whirl.nsf.gov., nsf.gov. NS cyclone.nsf.gov., nsf.gov. NS twister.nsf.gov., nsf.gov. DS, nsf.gov. DS, nsf.gov. RRSIG ar: . OPT UDPsize=1472 (510) 11:53:01.782937 IP (tos 0x0, ttl 251, id 24144, offset 0, flags [none], proto UDP (17), length 538) 209.112.123.30.53 > 71.246.241.146.28219: [udp sum ok] 38858- q: AAAA? cyclone.nsf.gov. 0/7/1 ns: nsf.gov. NS swirl.nsf.gov., nsf.gov. NS whirl.nsf.gov., nsf.gov. NS cyclone.nsf.gov., nsf.gov. NS twister.nsf.gov., nsf.gov. DS, nsf.gov. DS, nsf.gov. RRSIG ar: . OPT UDPsize=1472 (510) 11:53:01.785168 IP (tos 0x0, ttl 251, id 9456, offset 0, flags [none], proto UDP (17), length 538) 209.112.123.30.53 > 71.246.241.146.50745: [udp sum ok] 53248- q: A? twister.nsf.gov. 0/7/1 ns: nsf.gov. NS swirl.nsf.gov., nsf.gov. NS whirl.nsf.gov., nsf.gov. NS cyclone.nsf.gov., nsf.gov. NS twister.nsf.gov., nsf.gov. DS, nsf.gov. DS, nsf.gov. RRSIG ar: . OPT UDPsize=1472 (510) 11:53:01.786251 IP (tos 0x0, ttl 251, id 24145, offset 0, flags [none], proto UDP (17), length 538) 209.112.123.30.53 > 71.246.241.146.21482: [udp sum ok] 56185- q: AAAA? twister.nsf.gov. 0/7/1 ns: nsf.gov. NS swirl.nsf.gov., nsf.gov. NS whirl.nsf.gov., nsf.gov. NS cyclone.nsf.gov., nsf.gov. NS twister.nsf.gov., nsf.gov. DS, nsf.gov. DS, nsf.gov. RRSIG ar: . OPT UDPsize=1472 (510) So with edns-udp-size set to 512 it looks like the .gov servers (a.gov-servers.net, b.gov-servers.net) refuse to ever return the necessary glue for the nsf.gov DNS servers. Am I reading this right? Thanks, Bill Herrin -- William D. Herrin ................ herrin(a)dirtside.com bill(a)herrin.us 3005 Crane Dr. ...................... Web: <http://bill.herrin.us/> Falls Church, VA 22042-3004

7 13

Verizon Issues? East Coast US
by ML 03 Aug '11

03 Aug '11

Seeing some packet loss via Cogent. www.internetpulse.net seems to be lighting up.

8 12

Fwd: Service Provider Route Flap Damping Deployment Status Survey
by Shishio Tsuchiya 27 Jun '11

27 Jun '11

Dear NANOG Thanks for a lot of answer and comments to the survey. We will close this survey in 25th May 17:30 of the UTC time. If you could answer the survey,could you open url. https://www.surveymonkey.com/s/rfd-survey We will update our draft,and let you know. Regards, -Shishio -------- Original Message -------- Subject: Service Provider Route Flap Damping Deployment Status Survey Date: Fri, 18 Mar 2011 01:56:35 +0900 From: Shishio Tsuchiya <shtsuchi(a)cisco.com> To: nanog(a)nanog.org CC: shtsuchi(a)cisco.com, kawamucho(a)mesh.ad.jp, randy(a)psg.com, cristel(a)iij.ad.jp Dear NANOG, I'm Shishio,Cisco Systems Japan. I,Seiichi and Randy did presentation about "BGP topic" on JANOG27 which held 20th & 21st January 2011 in Kanazawa. http://www.janog.gr.jp/en/index.php?JANOG27%20Programs#qe7ec71d Randy explained "Route Flap Damping Considered Useable". http://ripe61.ripe.net/presentations/222-101117.ripe-rfd.pdf This report explains how to improve today's harmful RFD. We heard various opinion from bgp operators about RFD. So we took survey about "Service Provider Route Flap Damping Deployment Status" on janog(a)janog.gr.jp. We would like to hear more opinions to analyze current RFD operation,problem and so on. Could you please open the following url and answer the questionaire? https://www.surveymonkey.com/s/rfd-survey The JAPAN result summary is below. ----------------------------------- Q1.Do you use Route Flap Damping ? Yes: 5 No: 13 Q2.If you select No on Q1,why? Do not have the need: 3 Did not know about the feature: 2 No benefits expected: 3 Customers would complain:1 Because I read RIPE-378 :2 Other: 3 Q3.If you select Yes on Q1,what parameter do you use? Default parameters: 3 RIPE-178 : 0 RIPE-210 : 0 RIPE-229 : 0 Other: 3 Q4.Do you know Randy Bush et. al's report ''Route Flap Damping Considered Usable?'' Yes: 12 No: 7 Q5.IOS's max-penalty is currently limited to 20K. Do you need this limitation to be relaxed to over 50K? Yes: 10 No: 9 Q6.If you have any comments, please fill this box. -Our peer seems to have damping enabled, and our prefix gets damped sometimes. -We do not enable damping because we think that customers want a non-damped route. -From the perspective of a downstream ISP, if our upstream told us that an outage occurred because a route was damped, I may call and ask "is it written in the agreement that you will do this?" -We use damping pretty heavily -I had RFD turned on until this morning when I discovered our router has CSCtd26215 issues. I would like to turn on a "useful" RFD. ----------------------------------- other reference: https://tools.ietf.org/html/draft-shishio-grow-isp-rfd-implement-survey-01 https://tools.ietf.org/html/draft-ymbk-rfd-usable-00 Best Regards,

1 1

IPv6 - a noobs prespective
by Robert Lusby 14 Jun '11

14 Jun '11

As part of my role, I'm responsible, for a small (20 - 25 machine) network in the UK. When it comes to IPv6 I'm a complete noob. So ok - this is how I stand for IPv6: I "get" IPv4, I get NAT, I get why it's needed, and I get why it's evil. I know my IPv4 network inside and out, how DHCP runs and assigns addresses, how that ties in with our VPN, how everything gets channeled via the NAT to our ISP etc ... I also get why we need IPv6, that it means removing the NAT (which, surprise surprise also runs our Firewall), and I that I might need new kit for it. I am however *terrified* of making that move. There is so many new phrases, words, things to think about etc I want to, I'm keen to, and I know we have to, move to IPv6 - but at the moment it just seems so complicated - not least without affecting any IPv4 stuff. Just my own two pence from a noobie point of view. * On a side note - what's the best guide for upgrading a simple Windows network to run on IPv6? I'll take a read.

18 24

Resilient streaming protocols
by Aria Stewart 11 Jun '11

11 Jun '11

Anyone have any interest in a forward-error-corrected streaming protocol suitable for multicast, possibly both audio and video? Good for when there's some packet loss. ---- Aria Stewart

6 5

World of Warcraft may begin using IPv6 on Tuesday
by Kevin Day 08 Jun '11

08 Jun '11

For those that don't know, World of Warcraft is currently the largest online role playing game, with somewhere over 12 million subscribers. Version 4.1 of the game is expected to be released this Tuesday, which will be automatically pushed to all clients. The current Beta version of 4.1 has full IPv6 support. In the beta, it's automatically enabled if you have native IPv6 (non-6to4, non-Teredo). While Blizzard has been pretty silent about this, barring a last minute revert or delay of this patch, there are suddenly going to be a bunch more users that can potentially use IPv6. And these users are the type who are going to be especially sensitive to latency, jitter and packet loss, since this is a real-time game platform. For those of you with Help Desks who have to support users like this, the associated setting in the game's Options menu is apparently called "Enable IPv6 when available". It's apparently grayed out if you do not have IPv6 at all, unchecked by default if you are on 6to4 or Teredo, and checked by default if you are on native v6. The tooltip says: "Enables the use of IPv6, the technology behind the next-generation Internet. Requires IPv6 connectivity to the internet. Checking this box without IPv6 connectivity may prevent you from playing WoW." Anyone from Activision/Blizzard who would like to chime in with more details? :) -- Kevin

11 11