No "encapsulation" command on IOS 12.2(12a) ??
Show Version: Cisco Internetwork Operating System Software IOS (tm) 3600 Software (C3620-I-M), Version 12.2(12a), RELEASE SOFTWARE (fc1) flash image: System image file is "flash:c3620-i-mz.122-12a.bin" I'm trying to configure a FastEthernet sub interface for 802.1q VLANs, but theres no encapsulation command. I've googled it up for about 2 hours and have come up with nothing... the following command sequence is documented dozens of times: As shown on: http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120... interface fastethernet slot/port.subinterface-number encapsulation dot1q vlanid Any help would be appreciated.
int ethernet 0/0.0 encap 802.1q 532 You can't spec the encap on the parent interface. You must do it on the sub int. Owen --On Friday, October 24, 2003 02:49:15 AM -0700 Roman Volf <volfman@keystreams.com> wrote:
Show Version:
Cisco Internetwork Operating System Software IOS (tm) 3600 Software (C3620-I-M), Version 12.2(12a), RELEASE SOFTWARE (fc1)
flash image: System image file is "flash:c3620-i-mz.122-12a.bin"
I'm trying to configure a FastEthernet sub interface for 802.1q VLANs, but theres no encapsulation command. I've googled it up for about 2 hours and have come up with nothing... the following command sequence is documented dozens of times:
As shown on:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120... interface fastethernet slot/port.subinterface-number encapsulation dot1q vlanid
Any help would be appreciated.
This is what http://cio.cisco.com/go/fn is for. You need a "plus" version for VLAN support on the 3620. i.e. IP Plus, Enterprise Plus, etc. Your IP version below doesn't include the feature you're looking for. On Fri, 24 Oct 2003, Roman Volf wrote:
Show Version:
Cisco Internetwork Operating System Software IOS (tm) 3600 Software (C3620-I-M), Version 12.2(12a), RELEASE SOFTWARE (fc1)
flash image: System image file is "flash:c3620-i-mz.122-12a.bin"
I'm trying to configure a FastEthernet sub interface for 802.1q VLANs, but theres no encapsulation command. I've googled it up for about 2 hours and have come up with nothing... the following command sequence is documented dozens of times:
As shown on:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120... interface fastethernet slot/port.subinterface-number encapsulation dot1q vlanid
Any help would be appreciated.
---------------------------------------------------------------------- Jon Lewis *jlewis@lewis.org*| I route Senior Network Engineer | therefore you are Atlantic Net | _________ http://www.lewis.org/~jlewis/pgp for PGP public key_________
On Fri, 24 Oct 2003, Roman Volf wrote:
Show Version:
Cisco Internetwork Operating System Software IOS (tm) 3600 Software (C3620-I-M), Version 12.2(12a), RELEASE SOFTWARE (fc1)
flash image: System image file is "flash:c3620-i-mz.122-12a.bin"
I'm trying to configure a FastEthernet sub interface for 802.1q VLANs, but theres no encapsulation command. I've googled it up for about 2 hours and have come up with nothing... the following command sequence is documented dozens of times:
Any help would be appreciated.
You have an IP-only image as shown by the c3620-i in the filename. For VLAN support you need at least an "Plus" image. Depending on your hardware this may require more RAM and/or flash. -- Jay Hennigan - CCIE #7880 - Network Administration - jay@west.net WestNet: Connecting you to the planet. 805 884-6323 WB6RDV NetLojix Communications, Inc. - http://www.netlojix.com/
participants (4)
-
Jay Hennigan
-
jlewis@lewis.org
-
Owen DeLong
-
Roman Volf