Heres a followup. This is a show int on the interface. FastEthernet2/0 is up, line protocol is up Hardware is AmdFE, address is 0050.547b.e8c0 (bia 0050.547b.e8c0) Internet address is x.x.x.x/24 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, rely 255/255, load 5/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Queueing strategy: fifo Output queue 0/240, 905945 drops; input queue 0/240, 286 drops 30 second input rate 3397000 bits/sec, 1750 packets/sec 30 second output rate 2246000 bits/sec, 1989 packets/sec 55263194 packets input, 4227545542 bytes Received 185916 broadcasts, 0 runts, 0 giants, 286 throttles 1158 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast 0 input packets with dribble condition detected 52516038 packets output, 801075852 bytes, 0 underruns 0 output errors, 0 collisions, 4 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Now, those input errors are not reflected on the switch. Also, a show controller fastether 2/0 shows the following: Interface FastEthernet2/0 Hardware is AMD Laguna ADDR: 60D7F840, FASTSEND: 6002AEB4, MCI_INDEX: 0 DIST ROUTE ENABLED: 0 Route Cache Flag: 1 LADRF=0x0080 0x0100 0x0002 0x0000 CSR0 =0x00000072, CSR3 =0x00001044, CSR4 =0x0000491D, CSR15=0x00000180 CSR80 =0x00009900, CSR114=0x00000000, CRDA =0x0257CA40, CXDA=0x0257CFE0 CSR5 =0x00000001, CSR7 =0x00000820, CSR100=0x0000F000, CSR125=0x00005C3C BCR2 =0x00000000, BCR9 =0x00000001, BCR18 =0x000019E0, BCR22 =0x0000FF06 BCR25 =0x000000FF, BCR26 =0x00000080, BCR27 =0x00000010, BCR32=0x00004000 HW filtering information: Promiscuous Mode Disabled, PHY Addr Enabled, Broadcast Addr Enabled PHY Addr=0050.547B.E8C0, Multicast Filter=0x0080 0x0100 0x0002 0x0000 amdp2_instance=0x60D81170, registers=0x3D000000, ib=0x257C7E0 rx ring entries=64, tx ring entries=128 rxring=0x257C840, rxr shadow=0x60D81364, rx_head=32, rx_tail=0 txring=0x257CC80, txr shadow=0x60D81490, tx_head=54, tx_tail=54, tx_count=0 Software MAC address filter(hash:length/addr/mask/hits): 0x58: 0 0100.5e00.0006 0000.0000.0000 0 0x5B: 0 0100.5e00.0005 0000.0000.0000 0 0xC0: 0 0100.0ccc.cccc 0000.0000.0000 0 spurious_idon=0, filtered_pak=0, throttled=286, enabled=286, disabled=0 rx_framing_err=0, rx_overflow_err=1158, rx_buffer_err=0 rx_bpe_err=0, rx_soft_overflow_err=0, rx_no_enp=0, rx_discard=0 tx_one_col_err=0, tx_more_col_err=0, tx_no_enp=0, tx_deferred_err=0 tx_underrun_err=0, tx_late_collision_err=0, tx_loss_carrier_err=0 tx_exc_collision_err=0, tx_buff_err=0, fatal_tx_err=0 hsrp_conf=0, need_af_check=0 PHY registers: Register 0x00: 2100 784F 2000 5C01 01E1 0000 0000 0000 Register 0x08: 0000 0000 0000 0000 0000 0000 0000 0000 Register 0x10: 0000 0000 0000 FFFF 0000 0001 8062 Register 0x18: 8020 08A0 0000 1800 A3B9 Note the rx_overflow errors in line with the fe input errors. They seem to coincide with periods of unreachability but, we already replaced the card so.. Jason --- Jason Slagle - CCNA - CCDA Network Administrator - Toledo Internet Access - Toledo Ohio - raistlin@tacorp.net - jslagle@toledolink.com - WHOIS JS10172 -----BEGIN GEEK CODE BLOCK----- Version: 3.12 GE d-- s:+ a-- C++ UL+++ P--- L+++ E- W- N+ o-- K- w--- O M- V PS+ PE+++ Y+ PGP t+ 5 X+ R tv+ b+ DI+ D G e+ h! r++ y+ ------END GEEK CODE BLOCK------
Lock the ports on the switch to 100FD, try a different switch...
Heres a followup.
This is a show int on the interface.
FastEthernet2/0 is up, line protocol is up Hardware is AmdFE, address is 0050.547b.e8c0 (bia 0050.547b.e8c0) Internet address is x.x.x.x/24 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, rely 255/255, load 5/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Queueing strategy: fifo Output queue 0/240, 905945 drops; input queue 0/240, 286 drops 30 second input rate 3397000 bits/sec, 1750 packets/sec 30 second output rate 2246000 bits/sec, 1989 packets/sec 55263194 packets input, 4227545542 bytes Received 185916 broadcasts, 0 runts, 0 giants, 286 throttles 1158 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast 0 input packets with dribble condition detected 52516038 packets output, 801075852 bytes, 0 underruns 0 output errors, 0 collisions, 4 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out
Now, those input errors are not reflected on the switch.
Also, a show controller fastether 2/0 shows the following:
Interface FastEthernet2/0 Hardware is AMD Laguna ADDR: 60D7F840, FASTSEND: 6002AEB4, MCI_INDEX: 0 DIST ROUTE ENABLED: 0 Route Cache Flag: 1 LADRF=0x0080 0x0100 0x0002 0x0000 CSR0 =0x00000072, CSR3 =0x00001044, CSR4 =0x0000491D, CSR15=0x00000180 CSR80 =0x00009900, CSR114=0x00000000, CRDA =0x0257CA40, CXDA=0x0257CFE0 CSR5 =0x00000001, CSR7 =0x00000820, CSR100=0x0000F000, CSR125=0x00005C3C BCR2 =0x00000000, BCR9 =0x00000001, BCR18 =0x000019E0, BCR22 =0x0000FF06 BCR25 =0x000000FF, BCR26 =0x00000080, BCR27 =0x00000010, BCR32=0x00004000 HW filtering information: Promiscuous Mode Disabled, PHY Addr Enabled, Broadcast Addr Enabled PHY Addr=0050.547B.E8C0, Multicast Filter=0x0080 0x0100 0x0002 0x0000 amdp2_instance=0x60D81170, registers=0x3D000000, ib=0x257C7E0 rx ring entries=64, tx ring entries=128 rxring=0x257C840, rxr shadow=0x60D81364, rx_head=32, rx_tail=0 txring=0x257CC80, txr shadow=0x60D81490, tx_head=54, tx_tail=54, tx_count=0 Software MAC address filter(hash:length/addr/mask/hits): 0x58: 0 0100.5e00.0006 0000.0000.0000 0 0x5B: 0 0100.5e00.0005 0000.0000.0000 0 0xC0: 0 0100.0ccc.cccc 0000.0000.0000 0 spurious_idon=0, filtered_pak=0, throttled=286, enabled=286, disabled=0 rx_framing_err=0, rx_overflow_err=1158, rx_buffer_err=0 rx_bpe_err=0, rx_soft_overflow_err=0, rx_no_enp=0, rx_discard=0 tx_one_col_err=0, tx_more_col_err=0, tx_no_enp=0, tx_deferred_err=0 tx_underrun_err=0, tx_late_collision_err=0, tx_loss_carrier_err=0 tx_exc_collision_err=0, tx_buff_err=0, fatal_tx_err=0 hsrp_conf=0, need_af_check=0 PHY registers: Register 0x00: 2100 784F 2000 5C01 01E1 0000 0000 0000 Register 0x08: 0000 0000 0000 0000 0000 0000 0000 0000 Register 0x10: 0000 0000 0000 FFFF 0000 0001 8062 Register 0x18: 8020 08A0 0000 1800 A3B9
Note the rx_overflow errors in line with the fe input errors. They seem to coincide with periods of unreachability but, we already replaced the card so..
Jason
--- Jason Slagle - CCNA - CCDA Network Administrator - Toledo Internet Access - Toledo Ohio - raistlin@tacorp.net - jslagle@toledolink.com - WHOIS JS10172 -----BEGIN GEEK CODE BLOCK----- Version: 3.12 GE d-- s:+ a-- C++ UL+++ P--- L+++ E- W- N+ o-- K- w--- O M- V PS+ PE+++ Y+ PGP t+ 5 X+ R tv+ b+ DI+ D G e+ h! r++ y+ ------END GEEK CODE BLOCK------
We have an almost identical problem. I have a 3640 connected to a catalyst 2924XL. I have the switch and router both locked at 100/fdx. The crc error counters increment on the switch. According to cisco, this is related to bug id CSCdm49462. In short, when using ISL, the keeplives are not encap'd so the switch sees this as a crc error. The workaround is to disable keepalives on the router for that interface. Well we have tried this and this does not make a difference at all. We are still having lockups and continous crc errors. Bug id CSCdm49462 is a duplicate of CSCdm31600, which has been closed as there is a workaround (disable keepalives). If anyone can offer anything else on this I would very much appreciate it. (We have done the obvious and replaced cables and interfaces.) 2924XL: FastEthernet0/1 is up, line protocol is up Hardware is Fast Ethernet, address is 0001.4257.e241 (bia 0001.4257.e241) Description: ISL Trunk Feed to RHSC Core FastEthernet2/0 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 26/255, rxload 9/255 Encapsulation ARPA, loopback not set Keepalive not set Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:58, output 00:00:00, output hang never Last clearing of "show interface" counters 21:28:28 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 3788000 bits/sec, 2043 packets/sec 5 minute output rate 10293000 bits/sec, 2302 packets/sec 144755645 packets input, 235743734 bytes Received 154190 broadcasts, 0 runts, 0 giants, 0 throttles 89993 input errors, 89993 CRC, 0 frame, 0 overrun, 585 ignored 0 watchdog, 60165 multicast 0 input packets with dribble condition detected 153666041 packets output, 3705280485 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out 3640: FastEthernet2/0 is up, line protocol is up Hardware is AmdFE, address is 00e0.1edf.8ba0 (bia 00e0.1edf.8ba0) Description: RockHill Main and Colo Lans MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 10/255, rxload 26/255 Encapsulation ARPA, loopback not set Keepalive not set Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 1w2d Queueing strategy: fifo Output queue 0/40, 33091 drops; input queue 0/75, 370786 drops 5 minute input rate 10277000 bits/sec, 2335 packets/sec 5 minute output rate 4235000 bits/sec, 2078 packets/sec 1450782711 packets input, 3672702950 bytes Received 6487551 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast 0 input packets with dribble condition detected 1373258222 packets output, 2317298953 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Regards, Jeff
Lock the ports on the switch to 100FD, try a different switch...
Heres a followup.
This is a show int on the interface.
FastEthernet2/0 is up, line protocol is up Hardware is AmdFE, address is 0050.547b.e8c0 (bia 0050.547b.e8c0)
participants (3)
-
Jason Slagle
-
Jeff Wheat
-
Neil J. McRae