Hi All, I'm trying to bring up GigE link between 6509 and GSR. This is my problem: In the GigE interface on GSR says the interface is UP and line protocol is UP and in the GigE interface on 6500 says "not connected". Anyone have been in same situation? /michael --
On Sun, Feb 11, 2001 at 07:08:39PM +0100, Michael Kim wrote:
Hi All, I'm trying to bring up GigE link between 6509 and GSR. This is my problem: In the GigE interface on GSR says the interface is UP and line protocol is UP and in the GigE interface on 6500 says "not connected".
Anyone have been in same situation?
set port neg X/Y dis /Jesper -- Jesper Skriver, jesper(at)skriver(dot)dk - CCIE #5456 Work: Network manager @ AS3292 (Tele Danmark DataNetworks) Private: Geek @ AS2109 (A much smaller network ;-) One Unix to rule them all, One Resolver to find them, One IP to bring them all and in the zone to bind them.
Jesper Skriver wrote:
On Sun, Feb 11, 2001 at 07:08:39PM +0100, Michael Kim wrote:
Hi All, I'm trying to bring up GigE link between 6509 and GSR. This is my problem: In the GigE interface on GSR says the interface is UP and line protocol is UP and in the GigE interface on 6500 says "not connected".
Anyone have been in same situation?
set port neg X/Y dis
"autoneg off" is default in WS-X6516-GBIC. I'm runnig OSR6500 and WS-X6516-GBIC. otherwise this is what i have done : 1. rebooted whole system several time and enabled and disable interface several time. 2. tried with 3 different fiber and 4 different GigE GBIC SM LX, tried with other equipment without any problem. 3. tried with different GSR and 6500, tried between 6500s with same GBIC and fiber without any problem. 4. cleaned the fiberconnectors and the receiving input power(between -3dbm to -19 dbm) is -6.3 dbm on both side. The GBIC I have used is WS-G5486 on both side of the GigE link and I have also tried also with GBIC from 3Com.
/Jesper
-- Jesper Skriver, jesper(at)skriver(dot)dk - CCIE #5456 Work: Network manager @ AS3292 (Tele Danmark DataNetworks) Private: Geek @ AS2109 (A much smaller network ;-)
One Unix to rule them all, One Resolver to find them, One IP to bring them all and in the zone to bind them.
On Sun, Feb 11, 2001 at 07:53:46PM +0100, Michael Kim wrote:
Jesper Skriver wrote:
On Sun, Feb 11, 2001 at 07:08:39PM +0100, Michael Kim wrote:
Hi All, I'm trying to bring up GigE link between 6509 and GSR. This is my problem: In the GigE interface on GSR says the interface is UP and line protocol is UP and in the GigE interface on 6500 says "not connected".
Anyone have been in same situation?
set port neg X/Y dis
"autoneg off" is default in WS-X6516-GBIC. I'm runnig OSR6500 and WS-X6516-GBIC.
Hmm, the below works for me (on SX GBIC's) interface GigabitEthernet4/0 no negotiation auto set port negotiation 2/2 disable router#sh diag 4 SLOT 4 (RP/LC 4 ): 1 Port Gigabit Ethernet MAIN: type 43, 800-3955-03 rev A0 dev 994064 HW config: 0x00 SW key: 00-00-00 PCA: 73-3302-04 rev A0 ver 4 HW version 2.1 S/N CAB0436C1EC MBUS: MBUS Agent (1) 73-2146-07 rev B0 dev 0 HW version 1.2 S/N CAB0429AVBW Test hist: 0x00 RMA#: 00-00-00 RMA hist: 0x00 DIAG: Test count: 0x00000000 Test results: 0x00000000 L3 Engine: 1 - Standard OC48 (2.5 Gbps) MBUS Agent Software version 01.43 (RAM) (ROM version is 01.33) Using CAN Bus A ROM Monitor version 10.00 Fabric Downloader version used 13.06 (ROM version is 13.06) Primary clock is CSC 1 Board is analyzed Board State is Line Card Enabled (IOS RUN ) Insertion time: 00:00:09 (17:17:00 ago) DRAM size: 67108864 bytes FrFab SDRAM size: 134217728 bytes, SDRAM pagesize: 8192 bytes ToFab SDRAM size: 134217728 bytes, SDRAM pagesize: 8192 bytes 0 crashes since restart And the module in the 6509 is WS-X6408-GBIC /Jesper -- Jesper Skriver, jesper(at)skriver(dot)dk - CCIE #5456 Work: Network manager @ AS3292 (Tele Danmark DataNetworks) Private: Geek @ AS2109 (A much smaller network ;-) One Unix to rule them all, One Resolver to find them, One IP to bring them all and in the zone to bind them.
Hi all, Thank you all for the input. I thought I had disabled autoneg but I didn't. /michael Jesper Skriver wrote:
On Sun, Feb 11, 2001 at 07:08:39PM +0100, Michael Kim wrote:
Hi All, I'm trying to bring up GigE link between 6509 and GSR. This is my problem: In the GigE interface on GSR says the interface is UP and line protocol is UP and in the GigE interface on 6500 says "not connected".
Anyone have been in same situation?
set port neg X/Y dis
/Jesper
-- Jesper Skriver, jesper(at)skriver(dot)dk - CCIE #5456 Work: Network manager @ AS3292 (Tele Danmark DataNetworks) Private: Geek @ AS2109 (A much smaller network ;-)
One Unix to rule them all, One Resolver to find them, One IP to bring them all and in the zone to bind them.
-- ______________________________________ Michael Kim Telia Carrier & Networks Box 107 07, 121 29 Stockholm Sweden Tel : +46 8 4568907 Mobile : +46 706340646 E-mail : kim@telia.net mikael.m.kim@telia.se Visiting address : Globen, Arenavägen 57, plan 8 (rec. plan 9) 121 29 Stockholm Sweden _______________________________________
On Sun, Feb 11, 2001 at 07:08:39PM +0100, Michael Kim wrote:
I'm trying to bring up GigE link between 6509 and GSR. [snip] Anyone have been in same situation?
Several people were in early October 2000 on cisco-nsp See http://puck.nether.net/lists/cisco-nsp/ and the thread titled, strangely enough, "GSR/Cat Gig-e problem". I'd suggest you take your vendor-specif questions to vendor-specific fora. Cheers, Joe -- Joe Provo Voice 508.486.7471 Director, Internet Planning & Design Fax 508.229.2375 Network Deployment & Management, RCN <joe.provo@rcn.com>
participants (3)
-
Jesper Skriver -
Joe Provo -
Michael Kim