Hey, anyone had issues with A9K-MPA-20X1GE in ASR9001? It get disabled for us after 20 seconds finishing initialization, with such message. %PLATFORM-SCC-2-BAD_ID_HW : Failed Identification Test in 0/130/0 [1/0] The module in 0/130/0 in this router may not be a genuineCisco product.
On 10/25/2013 11:55 AM, Nikolay Shopik wrote:
Hey, anyone had issues with A9K-MPA-20X1GE in ASR9001?
Hi Nikolay, We're using them without problems. What software are you running? I did have major issues with flapping onboard 10G ports disabling TX. Regards, Remco Bressers Signet B.V.
On 25/10/13 14:08, Remco Bressers wrote:
We're using them without problems. What software are you running? I did have major issues with flapping onboard 10G ports disabling TX.
Tried on shiped 4.3.1 and now on 4.3.2, with same results. Also IIRC onboard ports only accept SFP+ rigth?
We use that combination without difficulty as well. -Bill
On Oct 25, 2013, at 17:10, "Remco Bressers" <remco@signet.nl> wrote:
On 10/25/2013 11:55 AM, Nikolay Shopik wrote: Hey, anyone had issues with A9K-MPA-20X1GE in ASR9001?
Hi Nikolay,
We're using them without problems. What software are you running? I did have major issues with flapping onboard 10G ports disabling TX.
Regards,
Remco Bressers Signet B.V.
Have you tried a different IOS? Ahad
On 25 Oct 2013, at 8:55 pm, Nikolay Shopik <shopik@inblock.ru> wrote:
Hey, anyone had issues with A9K-MPA-20X1GE in ASR9001?
It get disabled for us after 20 seconds finishing initialization, with such message.
%PLATFORM-SCC-2-BAD_ID_HW : Failed Identification Test in 0/130/0 [1/0] The module in 0/130/0 in this router may not be a genuineCisco product.
So far only 4.3.2 and 4.3.1. Probably gonna check it on 4.2 tree and more recent 5.1 On 25/10/13 17:14, Ahad Aboss wrote:
Have you tried a different IOS?
Ahad
On 25 Oct 2013, at 8:55 pm, Nikolay Shopik <shopik@inblock.ru> wrote:
Hey, anyone had issues with A9K-MPA-20X1GE in ASR9001?
It get disabled for us after 20 seconds finishing initialization, with such message.
%PLATFORM-SCC-2-BAD_ID_HW : Failed Identification Test in 0/130/0 [1/0] The module in 0/130/0 in this router may not be a genuineCisco product.
On Oct 25, 2013, at 7:23 AM, Bill Woodcock <woody@pch.net> wrote:
On Oct 25, 2013, at 6:21 AM, Nikolay Shopik <shopik@inblock.ru> wrote:
So far only 4.3.2 and 4.3.1. Probably gonna check it on 4.2 tree
We're running 4.2.3.
Sorry for the multiple posts… We're also running 4.3.0 with the combination successfully.
router.nrt.woodynet.net:!Image: Boot Image: /disk0/asr9k-os-mbi-4.3.0/0x100000/mbiasr9k-rp.vm router.nrt.woodynet.net:!Image: Boot Image: /disk0/asr9k-os-mbi-4.3.0/lc/mbiasr9k-lc.vm router.jnb.woodynet.net:!Image: Boot Image: /disk0/asr9k-os-mbi-4.2.3/0x100000/mbiasr9k-rp.vm router.jnb.woodynet.net:!Image: Boot Image: /disk0/asr9k-os-mbi-4.2.3/lc/mbiasr9k-lc.vm
We have this command on the interfaces as well:
transceiver permit pid all
…which was necessary to get it to support 1gb SFPs, in addition to the 10gb SFP+ transceivers. -Bill
I feel should be the hardware issue. On Friday, October 25, 2013, Nikolay Shopik <shopik@inblock.ru> wrote:
Hey, anyone had issues with A9K-MPA-20X1GE in ASR9001?
It get disabled for us after 20 seconds finishing initialization, with such message.
%PLATFORM-SCC-2-BAD_ID_HW : Failed Identification Test in 0/130/0 [1/0] The module in 0/130/0 in this router may not be a genuineCisco product.
participants (5)
-
Ahad Aboss -
Bill Woodcock -
Nikolay Shopik -
Remco Bressers -
Xu Hu