Hi NANOG, I promised to post an update down the line on what happened with my wireless situation. Here it is. I purchased 2x Ubiquity Bullet2's (2.4 GHz) and utilized our existing antennas. It has been working extremely well, pushing a stable 54 Mbps over the link without issue. Signal strength is consistently -40 dBm +/- 2 dBm, from about -80 dBm before! Total cost included 2x Bullets, 2x PoE adaptors, and approx 40 ft of STP cat5: $120. I have yet to see what happens in a big thunderstorm, but I extrapolate that they will be able to handle the EMP without going haywire like before. They have worked very well through conditions that our last setup would not. Thanks again for the input everyone! Peter -----Original Message----- From: Peter Boone [mailto:NANOG@Aquillar.com] Sent: June-18-09 9:46 PM To: nanog@nanog.org Subject: RE: Wireless bridge OK, from reading all the excellent feedback I've got on and off list I've attempted to compile a "quick" summary of findings/ideas/products so far. - RouterBoard is no good for this type of application. - Get a unit with radio/antenna integrated, PoE from inside the building (outdoor rated cat5, shielded I assume), lightning suppression for the PoE (properly grounded), and ensure the mast is properly grounded. - Get off the 2.4 GHz range. Move up to 5. As for licensed vs. unlicensed, I'm getting mixed input. I'm fairly certain that if the price is right and the frequency is 5GHz+, it won't be a factor. Also, I'll be very glad to separate the bridge from the client access points so that allows for more options. Every solution at this range can easily do 20+ Mbps so throughput is no longer a factor. - Products that support ARQ are highly recommended. - I'm hearing the same products mentioned over and over: - Motorola - Ubiquiti - Aironet (Cisco) - Aruba A number of individuals recommended products from other brands at low cost that meet these mentioned requirements too. I'm not going to bother with a spectrum analyzer. In the current implementation we tried channels 1, 6 and 11 for a few days at a time and found 1 to be the most reliable. Done. At this point an analyzer will tell me what I already suspect: there's a problem. I've researched the Fresnel zones and calculated out a few things with rough numbers and worst case. For one, the Fresnel zone is disrupted most if the obstruction is closer to the endpoints (e.g. antennas). In this case, this is fine as the antenna are mounted at the outermost corner of the buildings as close as possible to the other buildings, approximately 3 floors in the air. Other buildings become a factor near the middle. Based on channel 1's wavelength of 0.12438 m, and assuming 1 km apart (for simplicity sake. It's actually less), the Fresnel zone is largest in the center at approx 5.6 m radius. That could definitely be obstructed by rooftops, I'll have to take another look though. This radius cuts in half when the frequency is doubled, thus more evidence in favour of the 5 GHz+ range. Cool. Or we could just go with a good line of sight optical solution but they look too expensive, and this area can have very unforgiving fog/wind to disrupt things further. What if we tilt each existing antenna up towards the sky 10-20 degrees? Please correct me if I'm wrong. The current antennas are plates. I'm pretty sure they are polarized. I used to have a product sheet on these but a Google search doesn't turn up any useful results anymore (SmartAnt PCW24-03014-BFL). The way they are mounted to the poles might make it difficult to try rotating them 90 degrees, but worth another look. The coax between the AP and antennas are no longer than 30 feet. I've often wondered if a Pringle or Coffee Cantenna would work better than these! For right now I'll have the coax line and ends inspected for damage/softspots, check the grounding, and cover/re-cover the ends in large amounts of rubber/electric tape. I think we might try the Ubiquiti Bullet2 for approx $100 per side (PoE supply/lightning suppression, wiring included) and see what happens! If that doesn't work, no major loss and we'll move up to something more serious (the PoE and wiring will already be ready to go). I will have to look into pricing on some of these suggestions and figure out if we should even bother getting a Bullet but instead go straight to a better all-in-one solution. Thank you guys very much for the tips. Feel free to keep them coming! Peter