I could never get LACP + tagged VLANs to work on SwOS.Then again, it doesn't work reliably on RouterOS either, so I gave up. Spending more on hardware that is well supported is worth it versus my time and sanity.I think Ubiquiti pretty much has the "cheap hardware that works well, but commercial support lacking" market cornered.
thanks,
-Randy----- On May 18, 2020, at 5:43 PM, nanog <nanog@nanog.org> wrote:Yep, run SwichOS, prevents you from running things in software. 😊
Dennis Burgess, Mikrotik Certified Trainer
MTCNA, MTCRE, MTCWE, MTCTCE, MTCINE, MTCSE, HE IPv6 Sage, Cambium ePMP CertifiedAuthor of "Learn RouterOS- Second Edition”
Link Technologies, Inc -- Mikrotik & WISP Support Services
Office: 314-735-0270 Website: http://www.linktechs.net
Create Wireless Coverage’s with www.towercoverage.com
From: NANOG <nanog-bounces@nanog.org> On Behalf Of Mike Hammett
Sent: Monday, May 18, 2020 4:37 PM
To: Mauro Gasparini <mjgasparini@gmail.com>
Cc: nanog@nanog.org
Subject: Re: Switch for SFP+
That's a downfall of Mikrotik, they give you ultimate power. You can do some pretty atypical things on there.
-----
Mike Hammett
Intelligent Computing Solutions
Midwest Internet Exchange
The Brothers WISP
From: "Mauro Gasparini" <mjgasparini@gmail.com>
To: nanog@nanog.org
Sent: Monday, May 18, 2020 1:45:59 PM
Subject: Re: Switch for SFP+
It's clear then that I must use "bridge vlan" to achieve the goal I am looking for.
Now it's time for me to study, research and test on my side.
If I have any specific questions, I will draw on your experience.
Thanks a lot.El 15/5/20 a las 22:11, Travis Garrison escribió:
On the CRS 3xx line, use vlan filtering instead. This guarantees hardware offloading.
PS. Do not use this method on the 1xx or 2xx lines.
/interface bonding
add mode=802.3ad name=bond-inet slaves=ether9,ether10,ether8 transmit-hash-policy=layer-2-and-3
/interface bridge
add name=bridge vlan-filtering=yes
/interface bridge port
add bridge=bridge interface=bond-inet
add bridge=bridge interface=sfp1
/interface bridge vlan
add bridge=bridge tagged=bond-inet,sfp1 vlan-ids=201
Thanks
Travis
From: NANOG <nanog-bounces@nanog.org> On Behalf Of Mauro Gasparini
Sent: Friday, May 15, 2020 10:55 AM
To: nanog@nanog.org
Subject: Re: Switch for SFP+
This works well on my CRSs:
/interface bonding
add mode=802.3ad name=bond-inet slaves=ether9,ether10,ether8 transmit-hash-policy=layer-2-and-3
/interface bridge port
add bridge=br-cabase interface=bond-inet
add bridge=br-cabase interface=sfp1
But if I want to bridge vlans behind some bonding Instead of bridging phy interfaces, cpu explodes:
/interface vlan
add name=vl201-mmen vlan-id=201 interface=sfp1
add name=vl201-mment vlan-id=201 interface=bond-inet
/interface bridge port
add bridge=br-mment interface=vl201-mmen
add bridge=br-mment interface=vl201-mmentEl 15/5/20 a las 12:06, Mike Hammett escribió:
https://wiki.mikrotik.com/wiki/Manual:CRS3xx_series_switches#Bonding
-----
Mike Hammett
Intelligent Computing Solutions
Midwest Internet Exchange
The Brothers WISP
From: "Mauro Gasparini" <mjgasparini@gmail.com>
To: nanog@nanog.org
Sent: Friday, May 15, 2020 8:55:22 AM
Subject: Re: Switch for SFP+
Thanks. I am currently using CRS326-24G-2S+ (with routerOS) for this, but when I want to do vlan trunking through the bonding, cpu load grows from 3% to more than 90%.
I'm consulting Mikrotik's support in the meantime, because routerOS probably doesn't take advantage of the switch hardware as swOS would.El 15/5/20 a las 10:03, Alain Hebert escribió:
Hi,
Mikrotik is a decent product and I'm always amazed at their features set, but...
Using the UI to configuring the switch will punt too much traffic toward the CPU. However, it is possible to configure the switch fabric with the cli and attain the desired results.
It does not compare to a JNP QFX5100 or a Extreme Network x650, x670... etc.-----Alain Hebert ahebert@pubnix.netPubNIX Inc.50 boul. St-CharlesP.O. Box 26770 Beaconsfield, Quebec H9W 6G7Tel: 514-990-5911 http://www.pubnix.net Fax: 514-990-9443On 2020-05-14 15:11, Adam Thompson wrote:
Have you actually looked at Mikrotik switches? I don't like the OS, but the hardware does what you want it to.
If necessary, buy your SFP modules from FS.com and get them coded as Mikrotik modules at the factory - that's what we do for Cisco, Brocade, Juniper, Extreme, etc.
Even the top-of-the-line Mikrotik only costs US$899.
-Adam
Adam Thompson
Consultant, Infrastructure Services
100 - 135 Innovation Drive
Winnipeg, MB, R3T 6A8
(204) 977-6824 or 1-800-430-6404 (MB only)
athompson@merlin.mb.ca
www.merlin.mb.ca
From: NANOG <nanog-bounces@nanog.org> on behalf of Mauro Gasparini <mjgasparini@gmail.com>
Sent: Thursday, May 14, 2020 8:46:21 AM
To: Mehmet Akcin
Cc: nanog
Subject: Re: Switch for SFP+
Thank you. The problem is that to get a price lower than U$D 3000 I have to resort to a used device.
El 14/5/20 a las 01:08, Mehmet Akcin escribió:
Used Juniper QFX5100-48T will do it. Probably overkill but you can grab one cheap @ebay
On Wed, May 13, 2020 at 16:36 Mauro Gasparini <mjgasparini@gmail.com> wrote:
Good afternoon.
I'm looking for a switch with the following capabilities:
. transport for more than 20 gbps
. link aggregation LACP
. slots for SFP+
. seamlessly when trunking vlans through the link aggregation.
And essentially that doesn't exceed US$D 2000 and is compatible with
10GBASE-ER and/or 10GBASE-ZR modules that are not from the vendor itself
(e.g. SPFs: Huawei, Mikrotik, Sumitomo, OEMs).
If any of you have a good experience with a device that meets these
requirements (which are minimal with the exception of price and
compatibility) ?
Regards.
Mauro Gasparini--
Mehmet
+1-424-298-1903
