Hi Try looking at this company's line of products: http://www.itouchcom.com/ they used to be Xyplex. Arie On Tue, 10 Sep 2002, Charles Sprickman wrote:
Hello all,
Here's what I've found out. It's a mix. If any one solution looks to be the "winner" it's the roll-your-own solution. This is what I'm going for since it's relatively cheap for low-density installs. The only problem I'm finding is that it's tough to get a 1U box that has 2 PCI slots open. 2U seems overkill. Since Compact Flash adapters are cheap (about $20) and the cards themselves can be had for $59 (128MB), I'm going to go diskless. I'll probably use conserver, but I'll be giving rtty a try as well.
If anyone has pointers to cheap 1U or 2U's, I'm all ears. Just need a minimal box, don't need much CPU for this.
With about 13 replies, I can report the following:
Lantronix - http://www.lantronix.com/products/cs/scs820_scs1620/index.html
1 vote for, one against. The complaint was that the Lantronix has a very bad management interface.
I also noted that BBC is using a mess of these at Telehouse...
4 for.
"Under the covers, it's your average linux box with ttys0-ttys31. The portslave software is pretty nice, too. Offline data buffering and the ability to stick a hostname relationship with a serial port. [Ex: ssh2 bob:myserver@cyclades to connect to server myserver ]"
Another poster is using the cyclades and the digi, and if I'm reading him right, uses the Cyclades 48 port for smaller installations and the digi on larger.
Digi - http://www.digi.com/solutions/devtermsrv/cm/index.shtml Looks to run about $1800 for 16 ports
1 for (kind of). The poster has a large installed base and it mostly works and has a very high density. Apparently it's a two-piece system where a cable fans out to boxes that further split it. But if one of the splitters locks up, everything dasiy-chained through it locks up. This person is now using Cyclades (please correct me if I'm wrong on this one).
Equinox - 2 folks using these (cards).
"We use the Equinox SST-128P (theoretically expandable to 128 ports, comes in 16-port chunks) on Linux. Their linux drivers work well [...] It's aPCI card with a cable to an external plugboard with the 16 RJ-45s."
"I have had a bit of experience with Equinox (http://www.equinox.com/) gear and can recommend them. Their serial hubs will talk serial to almost anything out there and when plugged into cat5, tunnel those serial ports back to physical mappings on a host system. [...] Geared more towards industrial applications (what I'm using them for) but I have often considered slapping one in our telecomm rack to map serial ports on my local box to our various gear."
Cisco -
2 suggestions to use a 2511 or a 3620 with 16 port async cards. The 2511 would probably be a bit too slow if you enable ssh though...
Livingston -
2 for an old portmaster behind an ssh-able box (if you have the space)
Arula Systems (www.arula.com)-
1 vote for this, apparently a new company.
Build your own -
5 for this solution. Everyone is using FreeBSD, and the RocketPort cards seem to work better than the Cyclades cards under FreeBSD. 3 people are using conserver (www.conserver.com) to make it easier to manage. Paul Vixie shared the following (he gave permission to quote in full):
"We use RocketPort, FreeBSD, IronSystems, and ISC rtty.
http://www.rocketport.com/products/specs/rack16_foto.asp http://www.rocketport.com/products/specs/specs.asp?product=rp_pci
http://www.freebsd.org/ http://www.ironsystems.com/
ftp://ftp.vix.com/pub/vixie/rtty-4.0.shar.gz
This puts a BSD box in every POP, which is very useful for many reasons."
So there you are... Thanks for all the responses.
Charles