Dear Mr. Jeff, Thank you for your reply. Below is the complete output in question (l2 is short for l2transport). You are mentioning platform capabilities and that the default might have changed. How do I alter this? pe#sh mpls l2 vc 42 d Local interface: Po190.42 up, line protocol up, Eth VLAN 42 up Destination address: X.X.1.89, VC ID: 42, VC status: down Last error: Imposition VLAN rewrite capability mismatch with peer Output interface: none, imposed label stack {} Preferred path: not configured Default path: no route No adjacency Create time: 00:00:59, last status change time: 00:31:40 Last label FSM state change time: 00:00:18 Last peer autosense occurred at: 00:00:18 Signaling protocol: LDP, peer X.X.1.89:0 up Targeted Hello: X.X.0.2(LDP Id) -> X.X.1.89, LDP is UP Graceful restart: not configured and not enabled Non stop routing: not configured and not enabled Status TLV support (local/remote) : enabled/not supported LDP route watch : enabled Label/status state machine : remote invalid, LruRnd Last local dataplane status rcvd: No fault Last BFD dataplane status rcvd: Not sent Last BFD peer monitor status rcvd: No fault Last local AC circuit status rcvd: No fault Last local AC circuit status sent: DOWN PW(rx/tx faults) Last local PW i/f circ status rcvd: No fault Last local LDP TLV status sent: No fault Last remote LDP TLV status rcvd: Not sent Last remote LDP ADJ status rcvd: No fault MPLS VC labels: local 242, remote 1199 Group ID: local 0, remote 0 MTU: local 9216, remote 9216 Remote interface description: Remote VLAN id: 42 Sequencing: receive disabled, send disabled Control Word: Off (configured: autosense) SSO Descriptor: X.X.1.89/42, local label: 242 Dataplane: SSM segment/switch IDs: 0/0 (used), PWID: 142 VC statistics: transit packet totals: receive 0, send 0 transit byte totals: receive 0, send 0 transit packet drops: receive 0, seq error 0, send 0 pe# Anyone else: feel free to join in. Maybe we have any L2VC/PW ninjas watching. Best regards, Jonas Bjork
On 15 Nov 2015, at 1:26, Jeff Tantsura <jeff.tantsura@ericsson.com> wrote:
Been forever since i looked at cisco, however sounds like vc type mismatch. They used to have it as a platform capability, perhaps SW upgrade changed the default.
to my memory "show mpls l2 transport" should provide enough details.
Hope this helps
Regards, Jeff
On Nov 14, 2015, at 4:50 AM, Jonas Bjork <mr.jonas.bjork@me.com> wrote:
Hi, I am using a couple of AToM/EoMPLS tunnels in order to carry customer voice and data traffic across our IP/MPLS core, and it is currently working just fine. The first side consists of a Cisco 7600 router (rsp) and the other one is an HP A5500-HI routing switch with full LER/E-LSR capability. At the HP site, the tunnels are facing the access ports towards our premium end-customers; and on the Cisco PE I terminate the tunnels on one of the 2x10GE portchannel backbone links. There is vlan X on the HP side and vlan Y on the Cisco side - vlan rewrite is working perfectly - as long as I use IOS 12.
After upgrading the Cisco router software to IOS 15 the tunnels won't come up. sh mpls l2 vc Y d says: ... Last error: Imposition VLAN rewrite capability mismatch with peer ...
I use almost exactly the same Cisco configuration before and after the upgrade (only minor changes and nothing related to this) and I havn't touched the HP. Apparently they don't talk the same L2PW language. I wonder though, why now? We use service instances on the HP switchport as endpoint, we initiate the targetted LDP session in addition to the pseudowire handshake from a sub interface MPLS crossconnect. There is no MTU mismatch; not here - not anywhere.
Anyone heard of this issue or experienced it?
Best regards,
Jonas Björk SNE, Europe/Sweden (hope you guys will help me anyway:)